- 品牌：
- 型号：
- 规格：XECXW3000
- 材质：多款供选
- 形状：
- 粒度：220-800
- 适用范围：去除0.2mm以下毛刺
- 加工定制：
描述描述 after drilling, contour the bore edge to remove burrs
conditions
情况 tool revolutions 5000rpm
depth of cut 0.5mm
切削深度 0.5mm
feed rate 300mm/min
effectiveness on installation of xebec cross-hole deburringtool 效率
before 之前 tool used：cutter
manual processing with a cutter resulted in inefficiency andunstable finishing quality
after 之后 tool used：cross-hole deburring tool ceramic stonetype ez-pm-5b
full automation with marching centers was possible and qualitybecame stable
comparison对比over 20 times longer life than with an elastic grindstone.
over 10 times longer life than with a mounted vitrified wheel.superior edges and far fewer secondary burrs than with anelectro-deposited diamond bar or a mounted vitrified wheel.point processing with no damage to peripheral area.soft contact. suitable for automation. also easy-to-use with handgrinder.
■comparison of deburring finish of cross-hole burrs generated inø3.5mm drill processing
| material : s45c | tool rpm : ：5000rpm | processing time :1sec | bore diameter in primery processing : ø5mm | bore diameterin secondary processing : ø3.5mm
| material : aluminum alloy | tool rpm : ：5000rpm |processing time : 1sec | bore diameter in primery processing : ø5mm| bore diameter in secondary processing : ø3.5mm
use 使用for efficient use of cross-hole deburring toolschoose a head that is slightly larger than the bore diameter insecondary processing.
(this is good for both longer tool life and better fitting.)choose the coarsest one (gray color; equivalent to #220) forefficient deburring
(choose orange (equivalent to #400) or blue (equivalent to #800)for superior edge quality and surface roughness.)operate at approximately 80% of the maximum rpm for each toolsize.
(do not exceed maximum rpm.)first insert the head while rotating into the primary processinghole. and then touch the head slightly onto the burry area aroundsecondary processing hole by the flexible shaft.
※do not exceed? the maximum cutting load; 5n i.e.500gf.(bending displacement of 2mm)
if the bore diameter in primary processing is small compered ofsecondary processing the hole becomes oval.
so in order to obtain a uniform deburring process, slightly jigglethe head in the axial direction and rotate the tool in both theforward and reverse directions until the head fits the secondaryprocessing hole.
lineup 规格
目标孔直径
target bore diameter in primary processing
磨头尺寸
head size 磨头形状
head shape 产品编码 product code
灰色
gray equivalent to #220 橙色
orange equivalent to #400 蓝色
blue equivalent to #800
overø3mm ø3mm sphere
(ball)
ez-pm-3b ez-po-3b ez-pb-3b
ø3*3mm column
(cylinder)
ez-pm-3r ez-po-3r ez-pb-3r
overø4mm ø4mm sphere
(ball)
ez-pm-4b ez-po-4b ez-pb-4b
ø4*4mm column
(cylinder)
ez-pm-4r ez-po-4r ez-pb-4r
overø5mm ø5mm sphere
(ball)
ez-pm-5b ez-po-5b ez-pb-5b
ø5*5mm column
(cylinder)
ez-pm-5r ez-po-5r ez-pb-5r
overø6mm ø6mm sphere
(ball)
ez-pm-6b ez-po-6b ez-pb-6b
head: ceramic fiber stone (sphere: ø3 to 6, column:ø3 to 5）
shaft: ø1.5 x 40 mm
shank: ø3 x 30 mm
上海金炜五金机械有限公司无锡分部
蒋小姐
18626315008
新区长江路东方银座5-1-1201