随快速卷帘门的日渐增多，怎样安装快速卷帘门也成为了一个重要的问题。深圳市森腾门业免费提供安装指导。具体的安装步骤如下：
快速卷帘门轨道的安装
1、在快速门的两侧确定导轨安装位置，用锤线放出导轨基准线，放出导轨连接件固定螺栓十字线，导轨超过吊顶不小于90cm。
2、用冲击钻在墙柱上打出连接件固定膨胀螺栓孔，连接件的间距不得大于800mm，两端距导轨口130mm。先上下固几块连接件，将导轨贴上， 校正其垂直并点焊，导固定后再复一下导轨的垂直度，每米不得大于7mm，全长垂直度不得超过26mm。
3、将其余连接件装上，连接件与导轨之问采用点焊，每件连接件与一导轨间点焊点不少于6点，点焊的宽度不小于6mm，焊接处绝不应穿现象发生。采用不锈钢导轨时焊条采用不锈钢焊条。
快速卷帘门轴的安装
(1)快速门大轴安装前，先将挂板定好方向装到卷轴上，再把4-9片帘板装到挂板上并卷紧在卷轴上川铁丝扎牢。
(2)吊装快速门大轴，一定要注意安全，设专人指挥、人字梯、脚手架、手拉葫芦都要经过检查。快速门门安装时先将套上轴承及座的光轴塞入卷轴端孔中，对准位置后将轴承固定螺栓拧紧。
(3)卷轴上好后，可左右移动卷筒调节位置。同时用水平尺和水平管复核一下卷轴的水平。调整好后，光轴与卷轴满焊固定，光轴与轴承用支头螺钉固定。
(4)卷轴吊装时要特别注意不要碰坏卷在轴上的帘板，用钢丝绳捆扎时要垫木板。
产品英文详情介绍
with fast shutter doors of the increasing number, how to install fast shutter doors it has also become an important issue. shenzhen teng-door industry to provide free installation instructions. specific steps are as follows: fast shutter door rail mounting 1, determines the position of the guide rail is mounted at both sides of the door quickly, releasing the guide rail with a hammer baseline line, releasing the rail fixing bolt connecting member crosshairs, ceiling rail over not less than 90cm. 2, with the impact drill hit in the connecting member fixing wall studs expansion bolts, the pitch of the connecting member is not greater than 800mm, from both ends of the guide opening 130mm. first upper and lower fixing pieces connecting member affixed to the rail, and the vertical correcting spot welding, the fixed guide rails and then re about verticality, per meter not more than 7mm, the entire length of the vertical must not exceed 26mm. 3, the upper connecting member remaining attached, and the q rail connecting member by spot welding, spot welding points less than 6 points between each connecting member and a guide member, the width of the spot welding is not less than 6mm, welding should never wear phenomenon. when welding stainless steel stainless steel guide rod. fast shutter doors mounted shaft (1) before the shaft is mounted fast gate, siding first predetermined direction onto the spindle good, then 4-9 sheets attached to the hanging flap kawasho plate and wound up on a reel sizha prison. (2) large shaft hoisting speed doors, be sure to pay attention to safety, set up special command, ladders, scaffolding, chain hoists are checked. the optical axis of the spool end inserted into the first hole and the seat of the bearing sleeve fast gate door installed in the aligned position after the bearing fixing bolts are tightened. (3) shanghao spool, the spool can move around a position adjustment. while the horizontal ruler and horizontal tube double-check reels level. after a good adjustment, the optical axis of the reel fully welded fixing, fixing the optical axis of the screw head bearing support. (4) to pay special attention not to damage the rolled curtain lifting the spool shaft, when bundling mat board to wire rope.
查看其它相同标签的文章：卷帘
深圳市森腾门业有限公司
13825283196
qq: 478858588